收藏本站
NCL30000
The NCL30000 (refer to the block diagram ? Figure 1) is
composed of 4 key functional blocks along with protection
circuitry to ensure reliable operation of the controller.
I pr(peak)
I pr(t)
I in(peak)
I S (t)
I in (t)
? On-time Control
? Zero Current Detection Control
? MOSFET Gate Driver
? Startup and V CC Management
On Time Control
The on-time control circuitry (Figure 25) consists of a
precision current source which charges up an external
capacitor (C t ) in a linear ramp. The voltage on C t (after
removing an internal offset) is compared to an external
ON
MOSFET
OFF
Figure 24. Theoretical Switching Waveform
The LED current is compared to a reference and an error
signal is passed to the NCL30000 controller to maintain the
desired average level. This error signal adjusts the on-time
of the power switch to pass the required energy through the
flyback transformer to achieve proper regulation of the LED
load. Just like in a traditional PFC boost converter, the loop
bandwidth must be low enough to filter out the twice line
frequency ripple otherwise the power factor correction
element of the circuit will be compromised. In the event of
an open LED fault, a constant voltage loop regulates the
output voltage across the output capacitor to assure safe
operation.
control voltage and the output of the comparator is used to
turn off the output driver thus terminating the switching
cycle. A signal from the driver is fed back to the on-time
control block to discharge the C t capacitor thus preparing the
circuit for the start of the next switching cycle.
The state of V control is determined by the external
regulation loop and varies with the rms input voltage and the
output load. To achieve high power factor, the regulation
loop is designed so that in steady state, the V control value is
held constant over a line half cycle. This results in fixed on
time operation. The range of on-time is determined by the
charging slope of the C t capacitor and is clamped at 4.93 V
nominal. The C t capacitor is sized to ensure that the required
on-time is reached at maximum output power and the
minimum input line voltage condition. Because the ramp has
a wide dynamic range, the control loop can accommodate
wide variation of line voltage and load power range.
http://onsemi.com
12
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NCL30051LEDGEVB BOARD EVAL NCL30051 LED DRIVER
NCL30100ASLDGEVB BOARD DEMO SGL LAYER PWM DIM LED
NCL30105GEVB BOARD EVAL 80V 350 FOR LED DRV
NCP1013LEDGEVB BOARD EVAL 5W UNIV LED DRIVER
NCP1028LEDGEVB EVAL BOARD FOR NCP1028LEDG
NCP1216AFORWGEVB BOARD EVAL NCP1216A 35W
NCP1351LEDGEVB EVAL BOARD FOR NCP1351LEDG
NCP3065BBGEVB BOARD EVAL NCP3065 MR16 BOOST
相关代理商/技术参数
NCL30001 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:High-Efficiency Single Stage Power Factor Correction and Step-Down Offline LED Driver
NCL30001DR2G 功能描述:LED照明驱动器 ANA PFC CONTROLLER RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCL30001DR2G-CUT TAPE 制造商:ON 功能描述:NCL30001 Series 11.3 V Isolated Step-Down Single Stage Power Factor - SOIC-16
NCL30001LEDGEVB 功能描述:LED 照明开发工具 Programmers Development RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
NCL30002 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Power Factor Corrected Buck LED Driver
NCL30002DIM1GEVB 制造商:ON Semiconductor 功能描述:120V DIMMABLE HPF BUCK - Bulk
NCL30002DIM2GEVB 制造商:ON Semiconductor 功能描述:230V DIMMABLE HPF BUCK - Bulk
NCL30002DR2G 功能描述:LED照明驱动器 Power Factor Offline Buck LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N